Carr 124504 Super Hoop Multi-Mount Step User Manual download pdf

Super Hoop Multi-Mount Step Installation Instructions

Part No’s: 1

4501

4502

4504

Quality and Style that Endures

Follow the diagram and the

written directions carefully for a

proper, safe installation.

Should you encounter an

unusual, unforeseen problem,

contact our Technical Help Line

7:00 AM – 3:00 PM Pacific Time

(951) 719-1068

Visit our web-site at

www.CARR.com

Carr Pattern Co., Inc.

Materials Furnished:

Two step castings, four steel mounting brackets,

Instruction sheet and two hardware packs (Important!

Not all of the parts in these hardware packs may be

needed for proper installation).

Tools Needed:

One Phillips Screwdriver, two 1/2” open or box

wrenches, pencil, center punch, drill motor, sharp 1/8”

drill bit, sharp 5/16” drill bit,

1. These steps mount to an extremely strong part of your vehicle, the

back side of its rocker panels. For the proper position of the step, the

front edge of the seat while in normal driving position should be in

line with the center of the step. For personal preference or to avoid

any obstruction that may be on the backside of the rocker panel, the

step can be moved towards the front or the rear of the vehicle.

2. Assemble the steel mounting brackets to the step as shown in the

drawing, but only hand tighten.

3. When positioning the assembled step against the back side of the

rocker panel, be sure to avoid all bumps and screws to ensure that

the step is against a flat surface. Take a pencil and mark a vertical

line that lines up with the front edge of the seat, on the outside

painted surface of the pinch weld. (See diagram). Disassemble the

brackets from the step.

4. Measure 8 7/8” on each side of the marked vertical line and mark

two more lines on that same surface. The dimension between the

two outside marked lines should be 17 3/4”.

5. Measure 3/8” from the edge of the pinch weld where you marked

the other vertical lines and mark two horizontal lines, creating a

cross hair. NOTE: DOUBLE CHECK DIMENSIONS BEFORE

DRILLING! (Warning: when drilling holes leave at least 1/8” of

metal between the hole and the edge of the pinch weld).

6. Take a center punch and punch the center where the two sets of lines

cross.

7. Take a 1/8” drill bit and drill out the centered punched holes.

8. Enlarge the 1/8” hole with a 5/16” drill bit.

9. After drilling make sure that all the burrs are removed.

10. Now you will need to bend the tab on the back of each bracket as

shown on the diagram to conform to the body metal of your vehicle.

11. Once the tabs are bent to the correct angle, use the 5/16” x 5/8” hex

bolts with the 5/16” hex nuts and 5/16” washers to securely tighten

the brackets on the vehicle.

12. Using the top ¼” hole at the top of each steel mounting bracket, take

a 1/8” drill bit and drill holes into the body metal. Take the 5/8”

sheet metal screws provided and securely tighten. (Drilling at an

angle may be necessary due to interference or for proper alignment).

Place the step back into the brackets and securely tighten.

13. We advise putting silicone sealer around the areas where the steel

mounting brackets contact the body metal.

14.

After one month of use, go back and give all hardware a final

tightening.

WARNINGS!

 Do not over tighten the nuts and bolts or damage to the castings

and or stripping of the threads could result.

 FOR SAFE AND PROPER USAGE OF THIS PRODUCT, THE

MOUNTING INSTRUCTIONS MUST BE FOLLOWED

CAREFULLY AND COMPLETELY.

 The manufacturer and distributor of this product are in no way

responsible for the consumer’s failure to adhere to the warnings

and directions of these instructions in the event of damage to the

consumer’s vehicle, other properties and or personal injury.

Carr Pattern Co., Inc.

Warranty Policy

Finishes: Limited Lifetime

Structural Warranty: Limited Lifetime

Warranty Conditions:

a. All warranties start from consumer’s date of purchase.

b. A new product will be sent out immediately to replace a

warranty claim.

c. The above guidelines apply only to the Original Purchaser.

d. Original proof of purchase must be submitted for all warranty

and returns issues.

Warranty Limitations:

a. Warranty coverage extends ONLY to repair or replacement of

the CARR product. This warranty does not cover the cost of

labor, transportation, installation or removal of the product.

b. Warranty coverage does not extend to damage caused by:

collision, fire, theft, freezing, vandalism, riot, explosion or

object striking the product, or misuse of the product and/or the

vehicle on which the product is being installed.

c. Warranty coverage does not extend to damage caused by:

airborne fallout (chemicals, tree sap, etc.), stones, hail,

earthquake, water or flood, windstorm, lightning, the

application of chemicals or sealants subsequent to manufacture.

d. Warranty coverage does not extend to damages caused by:

normal wear and tear, abuse, modification or improper

installation of the product.

e. Warranty coverage does not extend to any economic loss or

extra expense including (without limitation), payment for the

loss of time or pay, inconvenience, storage, loss of vehicle use,

vehicle rental expense, equipment rental expense, lodging,

meals, or other travel costs.

Other Terms:

This warranty gives you specific legal rights and you may also

have other rights that vary from state to state. CARR does not

authorize any person to create for it any other obligation or

liability in connection with its products. ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT

IS LIMITED IN DURATION TO THE DURATION OF THIS

WRITTEN WARRANTY. PERFORMANCE OF REPAIRS AND

NEEDED ADJUSTMENTS IS THE EXCULSIVE REMEDY

UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED

WARRANTY. CARR SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM BREACH OF THIS WRITTEN

WARRANTY.*

*Some states do not allow limitations on how long an implied

warranty will last or the exclusion or limitation of incidental or

consequential damages, so that above limitations or exclusions

may not apply to you.

Guarantee: Every attempt has been made to manufacture and

distribute the finest quality products available. Our manufactured

products are guaranteed to be free of defects due to workmanship

or materials. Distributed products are subject to manufacturer’s

warranty only.

CARR ● 27447 Bostik Court ● Temecula CA 92590

1 2

Carr Pattern Co., Inc 1

Summary of Contents

Page 1 - Carr Pattern Co., Inc

Super Hoop Multi-Mount Step Installation Instructions Part No’s: 124501, 124502 & 124504 Quality and Style that Endures Follow th

Page 2

Pinch Weld Bend Tab Bend Tab Main Bolts Main Bolts This step fits the following vehicles: TOYOTA

Comments to this Manuals

No comments

Carr 124504 Super Hoop Multi-Mount Step User Manual

Browse online or download User Manual for For the car Carr 124504 Super Hoop Multi-Mount Step. CARR 124504 Super Hoop Multi-Mount Step User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Carr 124504 Super Hoop Multi-Mount Step